Abstract Thin a-C:H:Si:O:N films were deposited from plasmas fed hexamethyldisiloxane, oxygen and nitrogen, and characterized as a function of the partial pressure of oxygen in the feed, Rox. Deposition rates varied from 10 to 27 nm min-1. Surface roughness was independent of Rox, being around 10 nm. The films contain C=C and C=O, and also Si-C and Si-O-Si groups. Lower [C] and [N] but greater [O] and [Si] were measured in the films as Rox was increased. Refractive indices of ~ 1.5 and optical energy gaps which fell from ~ 3.3 to ~2.3 eV were observed with increasing Rox. The Urbach energy fell with increasing optical gap, which is characteristic of amorphous materials. Such materials have potential as transparent barrier coatings.

Thin a-C:H:Si:F:N films were studied as a function of the partial pressure of SF6 in plasma feed, RSF, together with tetramethylsilane and N2. Deposition rates varied from ~4 to ~19 nm.min-1. Surface roughnesses were typically less than 35 nm. Surface contact angles with water droplets, measured using goniometry, were all around 90°. Scanning electron micrography revealed surface particles, probably formed in the gas phase, of typical diameters ~8 μm. As revealed by Fourier transform infrared spectroscopy and energy dispersive x-ray spectroscopy, the films are plasma polymers with a carbon and silicon network. Most of the films contain ~ 60 at.% C, ~ 10 at.% Si, 20 at.% O and ~5 to 14 at.% N. Film doping with F rises to ~2 at.% as RSF is increased. The Tauc gap, calculated from ultraviolet-visible near infrared spectroscopic data, is controllable in the range of ~3.5 to 4.1 eV by a suitable choice of RSF. Fluorination causes the films to be softer and less stiff. Total deformation and stored energies are reduced compared to those of the film deposited at RSF = 0%. The modulus of dissipation increases from ~8% to a maximum of ~65% for the fluorinated films.

Abstract Recently, there has been growing interest in the incorporation of particles in plasma deposited thin films to creation of multifunctional surfaces. In this work a new hybrid methodology based on the plasma enhanced chemical vapor deposition (PECVD) of hexamethyldisiloxane combined to the reactive sputtering of TiO2 is proposed for the preparation of SiOxCyHz-TiO2 composite films. Specifically, the effect of the proportion of O2 in the plasma environment on the morphology, chemical structure, elemental composition, wettability, thickness and surface roughness, of the films was studied. Agglomerates of TiO2 (16-83 μm) were detected into the organosilicon matrix with the concentration of particulates growing with the percentage of oxygen in the feed. In general, there was elevation in the angle of contact of the surfaces as the oxygen supply increased. Interpretation is proposed in terms of the influence of the oxygen supply on the TiO2 sputtering rate and in the oxidation of plasma species.

Abstract In this work we discuss the wettability, chemical composition, surface morphology and optical transmittance of polyvinyl chloride (PVC) samples treated by Plasma Immersion and by Plasma Immersion Ion Implantation. The total pressure of N2 or SF6 was 6.66 Pa, for treatments of 900 s, applied rf power of 25 and 100 W, and the substrate temperature was about 298 K. In PIII, high voltage pulses of -2400 V at a cycle time of 30 µs and a frequency of 300 Hz were used. The wettability of the samples was assessed via contact angle measurements, which indicated either hydrophilicity or hydrophobicity, depending on the plasma composition. X-ray Photoelectron Spectroscopic analysis confirmed strong fluorine attachment to the surface after treatments using SF6 plasmas, and the presence of oxygen after treatments using nitrogen plasmas. Atomic Force Microscopy images showed that the roughness Rrms, depends on the plasma conditions. Optical transmittance in the visible region, T (λ), was increased by plasma immersion. The greatest contact angle observed was 142º (PI cathode), while the highest roughness was 213.2 nm. The highest optical transmittance in the visible region was around to 90% (PI anode).

This study reports the structural properties of zinc oxide thin films co-doped with aluminum and nitrogen (ZnO:Al-N) grown by RF magnetron sputtering from an AZO (ZnO with 2 wt% Al2O3) target under nitrogen (N2) atmosphere at room temperature (RT). Nitrogen partial pressures of 0.00, 0.10, 0.25 and 1.00 mTorr were used. The film thickness was around 270 nm. Ultraviolet-Vis-NIR transmittance (T) spectra of the films revealed T values of 80 to 85% in the 400 to 700 nm wavelength range. XRD results indicated that the films had a hexagonal wurtzite structure and were preferentially oriented in the (002) plane. Analyses by EDS indicated that the N atoms tend to be incorporated into the ZnO matrix at the expense of oxygen atoms. The ideal [N]/[Al] was obtained at a N2 partial pressure of 0.25 mTorr, producing a p-type film. For a [N]/[Al] of 1.53, the film also exhibited p-type conduction with an electrical resistivity of 31.92 Ω cm, mobility of 18.65 cm2/V s and carrier density of 1.22 x 1016 cm-3. The low carrier density is attributed to the energetically favorable formation of inactive nitrogen phases instead of acceptor-receiver-acceptor complexes, even at the ideal [N]/[Al].

Aluminum zinc oxide (AZO) thin films were synthesized on glass substrates by radio frequency (rf) magnetron sputtering from a metallic Zn-Al (5 at. %) target at room temperature. The morphological, structural, electrical and optical properties of the films were studied as a function of the sputtering pressure, which was varied from 0.1 to 6.7 Pa. X-ray diffraction (XRD) analyses revealed that the films obtained were polycrystalline, having a hexagonal wurtzite structure with a preferential orientation in the (002) plane. In addition, the crystallite size increased as a function of sputtering pressure. Owing to the re-sputtering of the Zn atoms from the growing film, the aluminum concentration presented a maximum value of 13 at. %. At pressures close to 0.16 Pa, we obtained films with values of electrical resistivity and mobility of 2.8 10-3 Ω cm and 17 cm2/Vs, respectively. Finally, our results indicate that the structure zone diagram proposed by Thornton and later modified by Kluth does not fully predict the structural/morphological behavior of the AZO films, since plasma interactions must also be taken into account. With the methodology used, transparent conductive electrodes can be deposited on substrates at low temperatures.

Cold plasmas fed trichloromethane-argon mixtures were used to treat cross-linked polyethylene (PE) to improve the adhesion of water-based paint. The effects of the plasma treatment undertaken at different percentages of CHCl3 in the plasma feed, CCl, were investigated using Infrared Spectroscopy in Diffuse Reflection (DR) mode, Scanning Electron Microscopy (SEM), Energy Dispersive X-ray Spectroscopy (EDS), X-ray Photoelectron Spectroscopy (XPS), goniometry for surface contact angle measurements, profilometry for roughness measurements, and paint adhesion tests. All the treatments modify the surfaces by introducing chlorine. Oxygen is present in the bulk and on the surfaces of the treated and untreated material. The treatments do not alter the bulk, but tend to increase the surface roughness and contact angle. When CHCl3 is present in the plasma subsequent paint adhesion is improved from a very poor classification of 4 to an excellent classification of 0 (assessed according to the appropriate Brazilian standards (BS EN ISO 2409:2007 and BS 3900-E6:2007A)). Surface roughness is not increased at low CCl but improved paint adhesion occurs for all CCl > 0. Although the causes of the improved paint adhesion with the plasma treatment are unclear, they may be related to the plasma activation of unsaturated carbon and oxygen functionalities.

RESUMO O compensado é um painel de madeira que pode ser utilizado tanto na indústria moveleira quanto na construção civil, devido ao seu uso estrutural. Entretanto, para ser utilizado na construção civil, o compensado necessita ser resistente aos agentes xilófagos e à umidade, sem comprometer suas propriedades mecânicas. Nesse aspecto, a termorretificação surge como uma alternativa de tratamento, que aumenta a resistência da madeira ao ataque de fungos e a sua estabilidade dimensional. Desse modo, o objetivo deste trabalho foi avaliar o efeito da termorretificação na qualidade de colagem de lâminas de madeira para a produção de compensado. Para isso, foram realizados os testes de molhabilidade utilizando o goniômetro digital, para lâminas tratadas nas três temperaturas e na amostra de controle. Além disso, foi realizado, o ensaio de cisalhamento na linha de cola, para testar a qualidade da colagem segundo a ABNT NBR ISO 12466-1 (2006). Com os resultados obtidos pode-se perceber que a superfície da madeira tratada se tornou mais hidrofóbica com o aumento da temperatura, e isso resultou também na diminuição da resistência ao cisalhamento na linha de cola, pois o adesivo utilizado (fenol-formaldeído) é à base de água, contudo, os requisitos normativos foram atendidos.

ABSTRACT Plywood is a wood panel that can be used both in the furniture industry and in construction due to its structural use. However, to be used in construction, it needs to be resistant against wood decay agents and water, without compromising its mechanical properties. The heat treatment is an alternative treatment which improves the wood resistance to fungi and improves its dimensional stability. Thus, the objective of this study is to evaluate the influence of the heat treatment with three different temperatures, 160, 180 and 200°C in the wettability of wood veneers and the shear strength in the bond line of the plywood produced with them. To do so, it was carried out the wettability testing using digital goniometer in the treated veneers at three temperatures and for the control specimen. Besides, it was carried out the shear strength in the bond line test, for testing the quality of bonding according to ABNT NBR ISO 12466-1 (2006). Because of the results obtained, it could be seen that the surface of the treated wood became more hydrophobic with increasing temperature, and this also resulted in a decrease in shear strength in the bond line, once the adhesive used (phenol-formaldehyde) is water based, however, the regulatory requirements have been met.

Thin films deposited from propanol-chloroform-argon mixtures by plasma enhanced chemical vapor deposition at different partial pressures of chloroform in the feed, CCl, were characterized after two years of aging and their characteristics compared with their as-deposited properties. Film thickness decreased and surface roughness increased with aging. Surface contact angles also increased with aging for the chlorinated films. For the film deposited with 40% chloroform in the feed the contact angle increased about 14°. Transmission infrared and Energy dispersive X-ray spectroscopy revealed that the films gain carbonyl and hydroxyl groups and lose chlorine and hydrogen on aging. Chlorination appears to make the films more durable. Delamination was observed for the unchlorinated films.

Plasma Electrolytic Oxidation (PEO) is promising for the processing of biomaterials because it enables the production of surfaces with adjustable composition and structure. In this work, aimed at the improvement of the bioactivity of titanium, PEO has been used to grow calcium phosphide coatings on titanium substrates. The effects of the addition of magnesium acetate to the electrolytes on the composition of the coatings produced during 120 s on Ti disks using bipolar voltage pulses and solutions of calcium and magnesium acetates and sodium glycerophosphate as electrolytes have been studied. Scanning electron microscopy, X-ray energy dispersive spectroscopy, Rutherford backscattering spectroscopy, X-ray diffractometry with Rietveld refinement and profilometry were used to characterize the modified samples. Coatings composed of nearly 50 % of Mg-doped hydroxyapatite have been produced. In certain conditions up to 4% Mg can be incorporated into the coating without any observable significant structural modifications of the hydroxyapatite.

Films were deposited from aluminum acetylacetonate (Al(acac)3) using a methodology involving reactive sputtering and low energy ion bombardment. The plasma was generated by the application of radiofrequency power to the powder containing electrode and simultaneously, negative pulses were supplied to the electrode where the substrates were attached. It was investigated the effect of the duty cycle of the pulses (Δ) on the properties of the coatings. Association of ion bombardment to the deposition process increased film thickness, structure reticulation and organic content. Ions from the deposition environment were implanted at the film-air interface or underneath it. Morphology and topography were altered depending on Δ. Considering the enhancement of Δ, it affected the flux of ions reaching the depositing interface and then the deposition rate, H content, crosslinking degree and surface microstructure. Alumina groups were detected in the infrared spectra, whereas the precipitation of amorphous alumina was confirmed by X-ray diffraction.

Cellulose is a polymer widely available in nature, however its applications may be restrict due to its hydrophilic character. The creation of hierarchical structures on the surface is one of the required factors to obtain the hydrophobicity of this material. In order to compare the morphological and chemical effects caused by the action of different gases in the creation of nanostructures on the cellulose surface, samples were exposed to oxygen (O2) and sulfur hexafluoride (SF6) plasma treatments. The changes in morphology after treatment prove that both the gases were able to create similar nanostructures in the material. The analysis of elemental composition and identification of functional groups on the sample surface showed that chemical modifications occurred differently for each treatment. Contact angle measurements revealed that samples treated by O2 plasma remained hydrophilic, whereas low receptivity to polar (θ > 120º) and non-polar (θ > 100º) liquids was observed for samples exposed to SF6 plasma.

RESUMO O trabalho em questão está relacionado ao projeto e construção de uma fonte de alta tensão em corrente contínua utilizando materiais e dispositivos adquiridos no comércio local visando sua aplicação no processo de pulverização catódica. Essa técnica permite a deposição de filmes finos de metais, óxidos e nitretos sobre substratos sólidos. Como teste de funcionamento e aplicação da fonte DC, com a mesma instalada em canhão de pulverização em alto vácuo, filmes finos de diferentes espessuras de cobre, aço inoxidável 304 e tungstênio foram depositados e estudados. Análise de espessura, morfologia, e resistência elétrica e resistividade foram conduzidas. Filmes com resistividade elétrica dependente das espessuras foram obtidos. A fonte DC se mostrou confiável em operação e permite a deposição de uma infinidade de materiais nas mais diferentes espessuras sobre vários tipos de substratos.

ABSTRACT This work is related to the project and construction of a DC high voltage power supply using materials and electronic devices acquired in local stores and to be used in sputtering proposes. The technique allows the obtainment of several kinds of thin films such as metals, oxides, nitrides and others upon solid substrates. In order to perform a test, the DC power supply was installed in a high vacuum system, connecting the power supply directly in a magnetron sputtering gun. Thin films of copper, stainless steel 304 and tungsten of several thickness were deposited upon commercial glass slides. The film thickness, surface morphology, electric resistance, sheet resistance and resistivity were herein analyzed. The power supply shows a good reliability in operation and allows the deposition of several materials in various thickness and substrates.

P20 steel, which is mainly used in plastic molds, was thermochemically treated by ion plasma nitriding and solid and gas carburization. In this work, the solid and gas carburization were performed at 925 ºC for four different durations. The ion plasma nitriding was performed at 520 ºC for four different durations. The thermochemical treatment increased the micro abrasive wear resistance of the studied material. The gas carburizing treatment resulted in a greater surface microhardness. Longer treatment times increased the effectiveness of the thickness layer in all cases. The solid carburization produced a larger thickness layer than the gas carburization and ion nitriding.

Paleometry is a promising research field that brings together different areas, such as physics and chemistry, applied to paleobiological issues. In spite of being recognized abroad, it is a new research field in Brazil. The most important characteristic is the application of mostly non-destructive techniques to the study of fossils. This work compiles some paleometrical applications to different geological contexts, such as the synthesis of hard skeleton in Corumbella werneri, geochemical aspects about fresh water bivalves from the Bauru Group and the exceptional preservation of arthropods from the Crato Member. Diffuse Reflectance Infrared (DRIFT) and Energy Dispersive X-ray Spectroscopy (EDX) were complementary to elucidate the types of skeletogenesys in Corumbella. In the case of the bivalves, DRIFT revealed to be important to elucidate aspects about death and fossilization. Among arthropods, morphological analysis with Scanning Electron Microscopy (SEM) associated with EDX was more profitable to understand fossilization process and paleoenvironmental implications.